Flash Dump Files of Satellite Receivers Free Download
Flash Dump Files of Satellite Receivers Free Download
Table of Contents
- Flash Dump Files of Satellite Receivers Free Download
- As for some, he installs it with an ordinary soldering iron, puts in on it, and re-cleans it.
- Use it with caution to avoid these things
- The magnifying glass is the only light source in the entire room
- Finally, we install the flash on the device
- 2- Next time
By moving to the section when clicking on the links below, which are arranged in English letters, for example, “Flash dump A Receiver, by clicking on it, it moves to the flashes that start with this letter, and you have every presentation dump.
On this page, the download is divided according to English letters.
Flash dump A Receiver
For beginners simple things to charge the flash should know
When dealing with the flash dump , the following must be followed:
1-You must have sufficient experience in dismantling and welding flashlights.
2-When removing the flash, be careful of the things next to it.
3-Before copying the flash, read it even if you need it a second time.
4-Not to be in a hurry and to say the defect is a flash, here it is necessary to verify the measurements of the fall.
5-The device often comes with a sound flash and we hurry and wipe it, but here is the major disaster.
Therefore, it is necessary to preserve its original reading first, so that it does not enter into a spiral. Please help me through the next
6-Make a folder for you in a safe place on the computer and put the correct flash dump readings which are
I tested it successfully to benefit you and benefit others when needed.
7- Type the name of the flash and the name of the device to make it easier for you to search
8-After you charge the flashlight and re-install it in the device and before you put plug of the device to electricity
Make sure that there are no welds between the legs of the flash dump and this is very important.
9- Be careful when cleaning the place of the flash after taking it off so as not to cause the destruction of lines
The board is skinny. Treat it carefully.
10-If a device comes to you to download or update software and you have not dealt with it before, do it first.
Even if something happens to him, I take a reading of his flash.
=====================
Important note about the flash or memory chip
Scanning and loading onto the flash drive may expose it to the following malfunctions
Be careful before downloading any program or patch on your server, you must know what the new program is by reading the information that came with the program and making sure that it fits your device or not.
Make sure that the new modification will increase the efficiency of the device
I know that loading many programs on the receiver shortens the life of the flash drive in the receiver
And I know that many modifications may disrupt the receiver due to an adjustment that you did not need
And the receiver has two flashlights
Flash for software and loader
And another flash for storing channels
(The flash is like any memory piece that has a shelf life, and frequent scanning and downloading exposes it to damage and disruption)
** Attention
Separating the receiver from the power supply during the update process may lead to damage to the receiver’s flash so that it lights a red dot and will not work after that unless it is changed, so be careful
An explanation of how to decompile, copy, program, and install the flash memory and the magnifying glass
flash definition
Flash: Ram Random Access Memory
Random memory is similar to the work of RAM in a computer, and it is what makes the software work
After it is installed, it is transferred to the receiver
Types of flashes
The flash memory in the receiver is a piece with several legs
And black in color, where the flash program itself is stored to control the receiver program
As for their sizes, they are 2 megabytes
They are manufactured by several companies and their prices are different
In the event of a failure of the receiver, the process of copying or replacing it is carried out according to the type of malfunction, and it is an easy process that can be carried out by a technician or an amateur.
Upload and install the flash chat
It is difficult to explain the process precisely, but the process needs to explain how to disassemble the flash and how to install it
Dismantling the flash through hot air. You warm the ends of the flash with the iron designated for this with hot air, but you must be careful lest you loosen all the pieces close to the flash, and some put on the flash a small piece of metal for fear that the heat will damage the flash and pull it with forceps and do not pull it until after it melts Tin so as not to damage the board or the legs of the flash.
This is for its jaw
As for the installation, you can put the flashlight on and re-heat it with the same device, and after making sure that the legs are in the correct places, protect it and press it to make sure that all the legs are aligned on the board.
As for some, he installs it with an ordinary soldering iron, puts in on it, and re-cleans it.
Explain how to disassemble the flash and how to install it
How to raise and install the flat
What are the tools and how to raise the flash in three seconds
We start with you
Required equipment
The user can use a regular iron because it is much cheaper than a hot air iron
It is preferable to rely on the hot air iron to raise and install the flash chat
The hot air iron is a count of d(2 tubes) one is oxygen and the other is acetylene 00
And we explain and say, Has anyone seen how many in the welding workshops he swallowed like a prisoner at the blacksmiths?
Count d 2 as a huge cylinder like a cooker cylinder, but an oasis longer than the second.
I’m sure most of you have seen what I’m talking about
But the hot air iron that removes the flashlight
It has a miniature form (one e, oxygen, and acetylene, which is found in the welding workshops of blacksmiths), but it produces the same ray of flame in its miniature form.
The shape of this flame can be controlled through a control knob
Like the same method that exists, it used large cylinders, of course, we will continue to explain
And we will talk about explaining the methods of use and their advantages
and how to get it at 00
You must put anything prepared, preferably, a piece of (aluminum) on the stove above it, in order to
It works to absorb excess heat and protect the flash from overheating
And of course, it will not cover the side that you will be working on
Use it with caution to avoid these things
Disadvantages of a hot air iron in order to eliminate its disadvantages
Remember here the disadvantages of this tool over a hot air iron
First: You know that the flame has two sides, one must be heated one after the other
In order for the flash to be lifted from its place, the time you need this tool is
One second for each side
As for the hot air iron, you will not be able to
Deciphering the one side e of the space at this time
Unless you are experienced and rehearsed
Second: The power of accuracy and definiteness of the goal, meaning that this tool is based on a tool
By ejecting an arrow-shaped flame and the thermal effect, this age is
The arrow that reaches its effective time is one millimeter, which means that it is almost accurate
Parallel to the laser beam, this thermal accuracy enables you to do, for example,
By heating one leg, it will not be affected by the man next to it
Thermal and does not emit an air diffuser, which is generous with the hot air iron
The effect of heat is through the outflow of air from the front of the pen
The thermometer includes a circle of not less than 3 cm with the smallest wave and even spreads the air
A larger area after it collides with the motherboard, which affects thermally
On the pieces next to the flame, thermally, and of course, if they are there
Resistors that are not adhesive next to the flame, it is possible to fly and not find them
Because of the strong air
Third: The material from which the motherboard is made in wood
Compressed and repeatedly directed air over a wide circuit causes liberation
This area is relatively safe from the effects of pressure on it
About this is the height of the area affected by the hot air
There is a kind of non-equatorial on the surface of the mother plate and this area is damaged
With a lot of repetition
Use it with caution to avoid these things
Explanation of the magnifying seh counting
This is the magnifying count that must be available to workers
In this field, because it makes you a flash of a large size that will not tire your eyes
And it will be mighty in discovering any closure that occurred between the ends of the flash because it is
Equipped with its own lighting
Receiver with its cover raised, see the degree of clarity of vision and the wonderful lighting on
the receiver although the
The magnifying glass is the only light source in the entire room
Explain how to copy flashes to all devices
flash copy
If you want to convert the device to Freeware, you must copy the flash and change the RAM
And if you want to copy the original flash, you can without changing the RAM, but it does not work for free
In some devices, it is now possible to charge a flash memory
It is installed on the motherboard without disassembling it by means of the interface called J-TAG
The program and the flash memory file, without the need to remove the flash memory
Unless it is broken, and this is rare.
Anyone can recharge the flash memory
from receivers,
The process takes only a quarter of an hour, and the device is back to work.
And I think digital device companies are starting to work on this thing
Recharge it without removing the flash
I offer you this simple explanation of how to decode, program, and install a flash memory
First, the tools you need:
hot air
Flash programmer + special programs
The most important of these tools is simple experience and practice in this field
The flash is removed from the damaged device and its edges are cleaned well of tin, as stated in the previous explanation
It is placed inside its adapter in a flash programmer, and then we follow the following
First, the flash is erased from the program on it
Secondly, choose the appropriate program for the device, or in other words, the program for the device
Already read it
Third, programming is done, and wait until the programming is finished
Finally, we install the flash on the device
Wait for the big surprise
Next time, I will explain how to program the flash while it is installed in the receiver without resorting to removing it and reprogramming it outside, and I will also solve the problems that members will face during the process of using the programmed Jettag
2- Next time
Wait for the big surprise
1- Next time I will explain how to charge the flash to the receivers
(And how was the process of charging the flash memory completed without resorting to removing the flash and programming it outside) through the Jettag programmer, which has become widely used
2- Next time
Peace, mercy, and blessings of God
Peace be upon you all, and here is the way to charge the flash while it is installed in the receiver
How to charge the flash for receivers
The process of charging the flash memory devices to receivers without resorting to removing the flash and reprogramming it outside through the Jettag programmer, which is now widely used to affect the computer’s BIOS from advanced tools and devices
Now I will start to explain about the programmer Gitaj, which is easy to implement, especially for beginners and amateurs
SIMPLE JTAG
It is the simplest Jettag programmer so far, it is made up of some resistors and a printer connection
Five resistors of 100 ohms each
(You can also use 150-ohm resistors in place of the 100-ohm resistors)
Male Printer Connector (25 Pin Male)
Now here is the link used to connect this programmer to the printer connection on your computer
As you can see, this link is made up of
Printer connection (25 male, male) and the other end (25 female male) printer connection
And the method of connecting the ends is parallel, i.e. 1- 1 2 -2 3 -3 …. 25 -25
Now we have finished drawing up a scheme for the simple Jettag programmer, which we will use to recharge the flash while it is installed in the receiver.
I will explain how to program the flash while it is installed in the receiver without resorting to removing it and programming it outside
I will also solve the problems that the members will face during the process of using the programmer
Communication problems between the programmer and the flash in your receiver
the problem
DCU PEEK ERROR – FLASH UNRECOGNIZED FLASH RETURNED
ERROR FLASH ERASING What are the problems
The third step
I will add a post that includes ways to add a flash receiver in the keys program, and I will also add a definition to the flash in your receiver if the jkeys program has not previously supported it
So, as you can see, this has many branches, and it is a very big topic
Now we will start the method of connecting the receiver, any receiver, to the Jettag program
The steps that must be connected between the programmer and the receiver are:
TMS
TDI
TD0
TCK
nTRST
GND
The Jetta link consists of twenty (bin) installed vertically
Also, note the presence of the arrow at the top of the guitar link, and this indicates the beginning of the numbering of the guitar link in the receiver.
Each receiver has a 20-pin Jettag connection
In general, the method of linking the programmed Jettag to the receiver is the same in all receivers
Which has a Jetage connector of 20 pins
And also the method of linking is the same between these receivers, but the difference is in the places of the port
But the connection method is the same, and here is the guide
First of all, the guitar connection in most receivers is, as I said, made up of 20 bins located in two rows 10 by 10
1 3 5 7 9 11 13 15 17 19
2 4 6 8 10 12 14 16 18 20
As you can see, the ends 2 4 6 8 10 12 14 16 18 20 are all connected to the landline
In the receiver, which of these parties is a landline
As a result, the parties that must be connected between the receiver and programmed Jettag are
Pin number 9 is the tip of the TMS
Pin No. 11 is TCK. tip
Pin No. 13 is the TDI tip
Pin 15 is TD0. pin
Pin No. 19 is the tip of interest
Which end of the dual terminals is the GND terminal, which is the landline, as we mentioned earlier
This was the method of numbering the Jettag link in any receiver that contains a 20-bin Jettag link.
Now we have been able to know the parties to connect between the receiver and the programmer of the Jetaj, and in the next post we will explain the method of preparing the program and also the method of reading the flash, scanning it, and reprogramming it using the Jetaj programmer and its operating program called JKEYS
And now here is the program used with the Jettag programmer to do this
Copy the flash and it is installed in the receiver and to all receivers
=======
Now here is how to set up the keys program
1- Unzip the keys file that you downloaded in the previous explanation
2- Now, among the files, you will find an executable program called keys, open it
Now, click on OK, and in this case, an error message will appear to you, which says that the program did not detect the programmer of the Gitaj that connects to the com connection in your computer.
As you noticed in that picture, the program first investigated the programmer of the Gita
that works through the com. link
But the programmer that we have works via the matching link in your computer, i.e. the Lpt connection
So in this case, we must prepare the program to investigate the programmer of our Jetaj, which works through the printer connection, and the method is:
Go to the File menu at the top of the program and choose Preferences
Now, after selecting the Preferences command, a box will appear
As you can see, the program is installed on the com1 mode, and since our programmer works on the printer connection, so we have to choose the Parallel Port command by clicking on the circle next to the Parallel Port command
Now at the bottom, there is a rectangle called Default Directory, which is the folder that you will use in the reading process and also store the flash that you read from the server to that folder
In this case, click on the Browse command
And choose the name of the folder that you will use to store the flash drives that I will read or deal with in the process of reading or copying to the flash in the receiver
After completion, press ok
Thus, we have finished the method of preparing the keys program to deal with the programmer of the Gita
============
Now here is how to use the program to deal with flash
1- Link the simple jtag programmer to the receiver
(connection method)
2- Connect the programmer to your computer using the printer connection
3- Turn on the receiver, i.e. supply it with electric current, and of course, it must be in the normal operating position
4- Open the keys program
5- Now the program will automatically check the number of the ISI processor in your receiver
But if it does not recognize the flash in your receiver,
This indicates that the connection between the programmer and the receiver is incorrect, and you must re-check the connections
Note: The cable that you will use to connect between the programmer of the Jetta and the receiver
The length of the connection should not exceed 13 cm
6- Now that the keys program has recognized the ISI number of the processor in your server, we will move now
The way to read the flash or copy it and the method is:
7- Click on the Flash Programming command
8- Now, after choosing that command, a box will appear in front of you
As you can see, that box contains the method that you must follow to do the programming process for the flash, which is:
- Disconnect the receiver from the mains (ie, turn it off by pressing the main power)
- Now press ok
- Now, in fewer than three seconds, restart the receiver by pressing the main power button
Some may ask why we disconnected the receiver from the electricity and then reconnected it again. The reason is:
Let’s make the program investigate the flash in your receiver from the first time
But if we did not say to disconnect the power from the receiver and we pressed ok directly, it happens to you sometimes in this case to the fact that the program does not investigate the flash number in your receiver, as it gives you an error sentence and will not be able to identify the flash number
So, follow the method I explained earlier, and the program will recognize the flash in the receiver directly from the first time
9- Now, after following this method, the program will detect the flash in your receiver and display it in a new box, as it:
- It will give you the flash number in detail, i.e. the number and the manufacturer, and you will find that information to your left, specifically in the Flash Info box
- He will also write the word Full in the Chip/Sector Programming field, specifically to the right of the program
Another important thing is that the rectangle containing the word “Full” must be white. The color of the rectangle must be white, but if it is gray, this means that the flash has not been properly investigated by the program or because the program does not support the flash
10- Now that the program has correctly investigated the flash memory in your receiver
We must now choose the name of the receiver from the IRD/Flash Selection field, specifically in the rectangle of the IRD Model whose value is UNKNOWN, and to the right of it there is a small triangle
Click on this small triangle and a list of servers will appear in front of you
Choose from the list the name of the receiver that you will deal with the flash inside and in this case we must choose the name of the receiver that you have
Now, after choosing the name of the receiver, we will deal with the flash inside it
We must first if the flash in the receiver we are dealing with is intact (that is if you want to do a reading of the flash file in your receiver to keep a backup copy for you
Which you will use if a receiver of the same type comes with a damaged flash inside. In this case, do not worry, you have a flash for the same receiver, which you read from a 100% working receiver
- In case you want to keep a backup copy of the flash file in your server
In this case, click on the read command
Which, after choosing it, will give you the folder in which you will store the file that you will read and store in a folder of your choice and with a name you choose
If you want, the program automatically names the name of the receiver and the flash number of the receiver from which you are reading the flash. In this case, click on the Save command
- Now the program will read the flash in your server, and after completion, click on reading, meaning that the reading has reached 100%. Now click on ok
A very important note:
After the Berne
Read the flash drive and store a copy of the Flash software on your computer
Go to the folder in which you stored the flash file that you read and follow this method to make sure that the program read the flash correctly
Take the left mouse pointer over the file that we read for the flash, and you will notice that Windows has given you the file size, and in your receiver, the file size should be 2 MB
But this reading may be incorrect
Compress the flash file that you read from the receiver, that is, compress it through the WinZip program
After the compression process, go to the compressed file that you made and check its size
- If its size ranges between 450 to 850 kilobytes, this indicates that the reading has been completed successfully
- If the size of the compressed file is between 50 to 350 kilobytes, this indicates that the reading is incorrect and therefore the flash file that we have read is also incorrect, since in both cases, the file size before compressing it gives you a value of 2 megabytes
Due to the largeness of the topic, I will explain how to read correctly, but next time
===========
How to convert a software file to a flash file
And how to extract the bot from the flash file for all devices
Software file to flash file
In some devices that carry STi processors, the software file can be converted into a flash file if these conditions are met:
1- The size of the software file should be greater than or equal to the size of the flash file in bytes.
2- If the end of the software file = End file: 2020 6107 when opening the file with Hex edit.
Here, either the software file is the same as a flash file if the file size is the same as the size of the flash file in bytes, such as Skybox, MyoTek, and other servers
It begins with evil eyes which is the name of the manufacturer and the end-of-file condition is met.
On some other devices, there is a definition or Header at the beginning of the file and it must be deleted.
Here is an example, we will choose any receiver from the Astra family
This is an example of converting a software file to any receiver from the receivers of the Astra family
The flash number is sst39vf160
- The number of checks is 512
The size of the vector is 4096 bytes or 1000 in hex.
The size of the flash file is 200,000 in hex or 2097,152 bytes
- Extract the bot from the flash file *
After storing the flash file, the bot can be extracted as shown in the following pictures:
These are the rest of the pictures in another file due to the large size
This is the method used to copy the bot for those who suffer from not downloading the entire flash file in the Jetta
- Connect the Jettag and make the necessary bot “wALL” and then erase the entire flash
- The file attached to the stickers from SA504 to SA511, which is the bot area in the SST39VF160 flash
- Choose the vector SA504 instead of FULL, then press PROGRAM and choose the file SA504.*** then OK
- Choose the next checklist and repeat the same process until you finish the eight checklists.
- Unplug the guitar and the receiver
Turn on the receiver. You will notice that the word “boot” is written on the device’s screen, then it stops.
- Using the software update program, make the necessary software.
Boot 21
Boot 39
(( Important note))
Do the same steps for each receiver in the same way, taking into account
It may require some behavior from the user from the slight difference
In the servers to any kind of other servers
After the simple differences that I explained, the idea remains one
Peace be upon you all